EZBUILD
Adhesives
Batteries
Duck Buggy
Electronics
EZbuilRC Planes
Hardware
Motors
PropsCategory: EZBUILD
EZBUILD
EZ Build Planes
Showing all 23 results
-
EZBUILD
45″ Long Flying Surfboard
$25.00
Add to cartEZ Build Surfboard concept by Mark Carew
Specs:
● Length 45”
● Width 14”
● Approx wt 14 oz
Parts:
Foam:
● 1- surfboard
● 1- elevator
● 2- board doubles
● 1-center keel
● 1-rudder
● 2-outside keels
● 1-Character option
Plywood:
● 1-two piece motor mount
● 1-battery mount
Misc:
● 2-horn/linkage stopper, right and left
● 1-10” elevator rod with Z bend
● 1-12” rudder rod with Z bend
● 1-5” double sided velcro
Power pack (optional, note: uses 500 mAh/3 cell battery))
● 1-Blue Wonder motor, 1700 kv
● 1- 10 Amp ESC
● 1- 8” x 4” prop
● 2- 9 gram servos
Assembly (use hot glue or Foamtac):
● Cut hinge bevels on surfboard/elevator and keel/rudder
● Use packing tape to make the hinges
● Glue board doubles on top
● Glue 3 keels to the bottom
● Glue battery velcro in the plywood battery mount
● Glue the battery mount to the bottom, front of the surfboard at the cutout
● Glue the linkage horns to the elevator and rudder
● Glue the elevator and rudder servos
● Install the rods
● Mount motor/ESC/receiver
● Slide in your surfer character
Throws: Elevator 1” up, ½” down, Rudder =/- 1”, CG is 14” from nose
-
Duck Buggy
RGB Strip Lights per foot
$1.00
Add to cart12 V strip lights perfect for 3 cell power Price per foot so mutiple orders will be shipped as one length as in you order 6 you will get a 6ft peice. Best to use a 3s Balance connector your able to use 1 color or and combination of Red Green and lue
-
EZBUILD
EZ Lazer Kit
$29.00
Read moreThis plane has always been a Parkflyer and a great night-flyer.Wow !This kit is an easy build. Good for flying in smaller areas. Responsive and an excellent flyer!Made from stiff White-Core Hobby Foam (I Like It).
Comes Partially AssembledSpecs:Wing Span 24 inchesLength 21 inchesThe EZ Lazer has Elevon Control this is available on all newer radios
Comes with:Laser Cut Foam Parts and Laser Cut Plywood, precision fit !1 motor mount2 pushrods2 Linkage Stoppers2 control horns installed2 pushrod GuidesVelcroSuggested Electronics-(Not Included)1- 2730 blue wonder1- 15 amp ESC2- 9g Budget Servos1- 8×4 Props withe the 1700 KV motorRecommended Lipo:1- 450 TO 850 mAh 3S battery (not included)Glue ..Hot GlueLazer foam Kit includes:8 Laser cut foam pieces that fit perfectly all you need to do is add the rudders and electronics
2 Control horns installes
2 Pushrods
2 Linkage stoppers
1 Plywood motor mount installedParts you will need to Fly this plane
Motor, 2)Servos, Receiver 4 or 6 channel (Only uses 3)
Transmitter(you need an Elevon Mixing Transmitter) -
EZBUILD
EZBuild Cub 40 On Hold Until June
$59.00
Read moreEZ Build Cub 40 Instructions Cub 40 Kit 40″ wingspan made from model airplane foam. The EZ Build Cub 40 is designed to be flown by novice to expert. It is strong and lightweight and, depending on the power set up, can do many 3D maneuvers. It can be set up with flaperons or spoilerons. …
-
Electronics
DSMX Receiver
$20.00
Add to cartProduct Specification
Dimension and Weight: 42.0mm(L) x 23.1mm(W), 8.7g Recommended voltage range: 3.5V to 8.5V (2S LiPo capable) Technology: DSMP with GEN2 SDR stack (DSMX / DSM2 compatibility) Highlight
DSMP 6-channel receiver is DSMX/DSM2 compatible that provides exceptional performance.
Quick Reference Guide
Failsafe
Bind receiver and current channel values will be saved. Failsafe will be activated when no signal is received for 2 seconds. All channels will be positioned to failsafe default. For this reason, it is recommended that the throttle should be at 0% while all other sticks are centred during binding.
1S LiPo Application
The minimum recommended safe supply voltage is 3.5V
NOTE:
- The battery must be capable of maintaining that voltage while delivering the required maximum load current to the receiver and servos. In some cases you MAY be able to operate at a lower voltage (for example a well discharged 1S LiPo cell) but you must test it in practice to be sure.
-
EZBUILD
Fenix 150
$89.00
Read moreThe Fenix 150 is made of durable EPP foam and has an 150 Centimeter ( 60 inch ) wingspan. This Kit includes the control Horns and Pushrods, the servo Slots are pre-cut and the motor mount is in place ready to mount your motor. It needs about 20 ounces of thrust to fly, we recommend …
-
EZBUILD
Vortex Kit
Sale!Original price was: $24.00.$20.00Current price is: $20.00.
Add to cartThe Vortex is now even Lighter! New Beefy Mount! Going to be an easy excellent night-flyer.Wow !This kit is an easy to build plane. Good for flying in smaller areas. Responsive and an excellent fly! Made from white core Hobby Foam (I Like It).Specs:Wing Span 23 3/4 inchesLength 18 inchesComes with:Laser cut Water Proof Foam1 motor mount mini2 pushrods2 Linkage Stoppers2 control horns2 pushrod Guides1 Built in Battery plywood with Velcro strapSuggested Electronics-(Not Included)1- 1804-1806 Quad Motor 2000KV1- 12-20amp ESC2- 9g Budget Servos2- Linkage Stoppers1- 5×4.5 3 Blade PropRecommended Lipo:1- 450 to 650 mAh 3S battery (not included)Glue ..Hot Glue or Foamtac works well(also Foam Safe CA if you like, always use kicker with Foam Safe CA )Paint; I used spray from Lowes , Just use light coats , it did no damage to the foam. Let it dry for 5 min and another light coat if needed .Vortex foam Kit includes:
8 Laser cut foam pieces that fit perfectly and are painted and partially assembled
2 Control horns
2 Pushrods
2 Linkage stoppers
1 Plywood motor mountParts you will need to Fly this plane
18XX to 23XX, 22XX quad motor or equivalent and prop to match
ESC (20 amp) and a 500 mah 11,1v lipo
Foamtac Glue or Hot Glue
Receiver 4 or 6 channel {only 3 needed)
Transmitter(you need an Elevon Mixing Transmitter)
