Shop
Showing all 60 results
-
EZBUILD
45″ Long Flying Surfboard
Rated 5.00 out of 5$25.00Add to cartEZ Build Surfboard concept by Mark Carew
Specs:
● Length 45”
● Width 14”
● Approx wt 14 oz
Parts:
Foam:
● 1- surfboard
● 1- elevator
● 2- board doubles
● 1-center keel
● 1-rudder
● 2-outside keels
● 1-Character option
Plywood:
● 1-two piece motor mount
● 1-battery mount
Misc:
● 2-horn/linkage stopper, right and left
● 1-10” elevator rod with Z bend
● 1-12” rudder rod with Z bend
● 1-5” double sided velcro
Power pack (optional, note: uses 500 mAh/3 cell battery))
● 1-Blue Wonder motor, 1700 kv
● 1- 10 Amp ESC
● 1- 8” x 4” prop
● 2- 9 gram servos
Assembly (use hot glue or Foamtac):
● Cut hinge bevels on surfboard/elevator and keel/rudder
● Use packing tape to make the hinges
● Glue board doubles on top
● Glue 3 keels to the bottom
● Glue battery velcro in the plywood battery mount
● Glue the battery mount to the bottom, front of the surfboard at the cutout
● Glue the linkage horns to the elevator and rudder
● Glue the elevator and rudder servos
● Install the rods
● Mount motor/ESC/receiver
● Slide in your surfer character
Throws: Elevator 1” up, ½” down, Rudder =/- 1”, CG is 14” from nose
-
Batteries
30 Amp Brushless Motor ESC
$20.50Add to cart30 amp esc with a 5V 2Amp BEC for Brushless Motors -Input Voltage: 2-3cells lithium battery or 5-9 cells NiCd/NIMh battery. -Compatible with: 400-450 helicopters / Aircraft or Quad-Rotor Multi RC Helicopter -Size: 45mm (L) * 24mm (W) * 11mm (H). -Works well with 2836 motor for Vortex BFV 40
-
Duck Buggy
RGB Strip Lights per foot
$1.00Add to cart12 V strip lights perfect for 3 cell power Price per foot so mutiple orders will be shipped as one length as in you order 6 you will get a 6ft peice. Best to use a 3s Balance connector your able to use 1 color or and combination of Red Green and lue
-
Adhesives
FoamTac 2oz
$11.99Add to cartFOAM-TAC is perfect for all types of foam including EPP, EPO, DEPRON, ETC. It also works great on balsa wood, carbon fiber and 3D printed parts. FOAM-TAC’S improved formula now contains UV blockers so that it can be used in the field in direct sunlight without any yellowing or degrading. We’ve also added a special …
-
Motors
D2836 1400KV motor
$19.50Add to cartD2836 Outrunner Brushless Motors Motor Diameter: 28mm Motor Length: 36mm Shaft Diameter: 3.17mm Shaft Length: 14mm Weight: 78g Mounting Hole Size: M3.0, pitch 16mm M3.0, pitch 19mm Mounting Hole Depth: 4mm Max. Order Name RPM/V No-load Current (7.4V) Max. Amps Batteries Propeller D2836/14 1400 0.8A 28A 2-3S Lipo 10×5
-
Adhesives
FoamTac 1oz
$9.00$8.00Read moreFOAM-TAC is perfect for all types of foam including EPP, EPO, DEPRON, ETC. It also works great on balsa wood, carbon fiber and 3D printed parts. FOAM-TAC’S improved formula now contains UV blockers so that it can be used in the field in direct sunlight without any yellowing or degrading. We’ve also added a special …
-
Fenix Planes
Fenix 60 Glider
$15.00$10.00Read moreFenix 60 24″ Wingspan Made of flexible EPP foam (NOT A STYROFOAM), which is extremely durable. Very easy to assemble, the models come pre-balanced. The excellent airfoil wing profile gives long flights. Very tough and suitable for children. Can be converted to radio control. Comes in attractive and bright colors.
-
EZBUILD
EZ Lazer Kit
$29.00Read moreThis plane has always been a Parkflyer and a great night-flyer.Wow !This kit is an easy build. Good for flying in smaller areas. Responsive and an excellent flyer!Made from stiff White-Core Hobby Foam (I Like It).
Comes Partially AssembledSpecs:Wing Span 24 inchesLength 21 inchesThe EZ Lazer has Elevon Control this is available on all newer radios
Comes with:Laser Cut Foam Parts and Laser Cut Plywood, precision fit !1 motor mount2 pushrods2 Linkage Stoppers2 control horns installed2 pushrod GuidesVelcroSuggested Electronics-(Not Included)1- 2730 blue wonder1- 15 amp ESC2- 9g Budget Servos1- 8×4 Props withe the 1700 KV motorRecommended Lipo:1- 450 TO 850 mAh 3S battery (not included)Glue ..Hot GlueLazer foam Kit includes:8 Laser cut foam pieces that fit perfectly all you need to do is add the rudders and electronics
2 Control horns installes
2 Pushrods
2 Linkage stoppers
1 Plywood motor mount installedParts you will need to Fly this plane
Motor, 2)Servos, Receiver 4 or 6 channel (Only uses 3)
Transmitter(you need an Elevon Mixing Transmitter) -
EZBUILD
EZBuild Cub 40 On Hold Until June
$59.00Read moreEZ Build Cub 40 Instructions Cub 40 Kit 40″ wingspan made from model airplane foam. The EZ Build Cub 40 is designed to be flown by novice to expert. It is strong and lightweight and, depending on the power set up, can do many 3D maneuvers. It can be set up with flaperons or spoilerons. …
-
EZBUILD
Fenix 80 Glider
$20.00$17.00Read moreFenix 80 Made of flexible EPP foam(NOT A STYROFOAM), which is extremely durable. Very easy to assemble, the models come pre-balanced. The excellent airfoil wing profile gives long flights. Very tough and suitable for children. Can be converted to radio control. Comes in attractive and bright colours.
-
EZBUILD
Fenix 120
$49.00$44.00Read moreThe Fenix 120 is made of durable EPP foam and has an 120 Centimeter ( 47 inch ) wingspan. This Kit includes the control Horns and Pushrods, the servo Slots are pre cut and the motor mount is in place ready to mount your motor. you have to glue 1 wingtip on with Hot Glue …
-
Motors
Keda A3628 For the Fenix 150
$24.50Read moreA36-28S KV1140 Minium ESC 30A Battery 3S Lipo Prop 9*7 to 10*5 Motor Diameter: 37.4mm Motor Length: 30mm Shaft Diameter: 5.0mm Shaft Length: 20mm Weight: 79g Mounting Hole Size: M3.0, pitch 25mm Mounting Hole Depth: 4mm Max. Includes the X Mount and Prop Adapter Click here for assembly Directions
-
Electronics
DSMX Diversity Receiver
$20.00$18.99Add to cartSpecification
Type: DSMX Compatible Full Range Receiver with Diversity Antenna Number of Channel: 6 Modulation: DSMX Compatible (Also DSM2 backward Compatible) Band: 2.4 GHz Dimension: 30(L) x 18(W) x 11(H) mm Weight: 4.54g Voltage Range: 3.45 – 8.4 V RCgroups discussion
http://www.rcgroups.com/forums/showthread.php?t=1773138User Manual re-direct link (Thanks to John [JJ604 RCgroups] in helping us with this user manual.)
http://www.lemon-rx.com/index.php?route=information/information&information_id=7How dual antennas work
An independent processor monitors an incoming signal and choose the appropriate antenna for reception. This allows 2 different location for installing the antennas along with different orientation. Satellite is no longer needed for receiver diversity. This greatly reduces weight with increased overall reliability in comparison to the use of a primary receiver with satellite receiver.
Photo showing below is the diversity receiver for end-pin stabilizer. The same diversity receiver is also used in this product.
Highlight
-True diversity dual antennas with independent processor for monitoring singal on both antennas
– Antennas extended for carbon fuselage / metalic structure installation
– FailSafe for all channels via press of a button
– DSMX Satellite portUnderstanding the receiver (Showing DSMX 6-channel non-diversity receiver)
Binding
1) Plug bind plug to the receiver.
2) Provide power to the unit. LED flashes quickly.
3) Enable bind mode in transmitter and ensure distance separation of 2 meters from receiver. Solid LED light means binding is completed.
4) Remove bind plug.Failsafe Enable (Video showing 10-Channel receiver)
Video:https://www.youtube.com/watch?v=FyW1v12dv_k
1) Bind the receiver and do not remove bind plug.
2) Upon successful binding, set the transmitter sticks / channels to the desired failsafe position.
3) Press the side pushbutton to save the current position in failsafe mode.
4) Check for green light on. Green light on indicates failsafe is successfully enabled.
5) Remove bind plug and power cycle the receiver.Failsafe Disable (Video showing 10-Channel receiver)
Video:https://www.youtube.com/watch?v=xpb1tvBvA2E
1) Bind the receiver and do not remove bind plug. If green light is on Failsafe is currently enabled, pressing the side pushbutton will disable Failsafe.
2) Check for green light off indicates Failsafe disabled.
3) Remove bind plug and power cycle the receiver.Note:
1) This is not a Spektrum DSMX or DSM2 product, nor is it a copy of a Spektrum DSM2 or DSMX product. The Spektrum, DSMX and DSM2 brand is a trademark of Horizon Hobby, Inc.
2) This is not an underground black market fake Spektrum product. Lemon Rx quality is guaranteed.
3) Lemon Rx products are tested to be compatible with Spektrum’s DSMX and or DSM2 product (Spketrum, DSMX and DSM2 are the registered trademark of Horizon Hobby, Inc.). -
Fenix Planes
Fenix 150
$89.00Read moreThe Fenix 150 is made of durable EPP foam and has an 150 Centimeter ( 60 inch ) wingspan. This Kit includes the control Horns and Pushrods, the servo Slots are pre-cut and the motor mount is in place ready to mount your motor. It needs about 20 ounces of thrust to fly, we recommend …
-
Fenix Planes
Fenix 100
$39.00$34.00Read moreThe Fenix 100 is made of durable EPP foam and has an 100 Centimeter ( 40 inch ) wingspan. This Kit includes the control Horns and Pushrods, the servo Slots are pre cut and the motor mount is in place ready to mount your motor. It needs about 10 ounces of thrust to fly, we …
-
EZBUILD
Vortex Kit
$24.00$20.00Add to cartThe Vortex is now even Lighter! New Beefy Mount! Going to be an easy excellent night-flyer.Wow !This kit is an easy to build plane. Good for flying in smaller areas. Responsive and an excellent fly! Made from white core Hobby Foam (I Like It).Specs:Wing Span 23 3/4 inchesLength 18 inchesComes with:Laser cut Water Proof Foam1 motor mount mini2 pushrods2 Linkage Stoppers2 control horns2 pushrod Guides1 Built in Battery plywood with Velcro strapSuggested Electronics-(Not Included)1- 1804-1806 Quad Motor1- 12-20amp ESC2- 9g Budget Servos2- Linkage Stoppers1- 5×4.5 3 Blade PropRecommended Lipo:1- 450 to 650 mAh 3S battery (not included)Glue ..Hot Glue or Foamtac works well(also Foam Safe CA if you like, always use kicker with Foam Safe CA )Paint; I used spray from Lowes , Just use light coats , it did no damage to the foam. Let it dry for 5 min and another light coat if needed .Vortex foam Kit includes:
8 Laser cut foam pieces that fit perfectly and are painted and partially assembled
2 Control horns
2 Pushrods
2 Linkage stoppers
1 Plywood motor mountParts you will need to Fly this plane
18XX to 23XX, 22XX quad motor or equivalent and prop to match
ESC (20 amp) and a 500 mah 11,1v lipo
Foamtac Glue or Hot Glue
Receiver 4 or 6 channel {only 3 needed)
Transmitter(you need an Elevon Mixing Transmitter)